5810 SDS
===================================================================================================================
Section 1 -- PRODUCT AND COMPANY IDENTIFICATION
===================================================================================================================
PRODUCT NUMBER HMIS CODES
Health 3
5810 Flammability 3
Reactivity 0
MANUFACTURER'S NAME: ADDRESS:
Cumberland Products Incorporated 50 Commerce Parkway
Hodgenville, KY 42748
EMERGENCY PHONE : (800) 424 - 9300 DATE PRINTED : 11/27/2013
INFORMATION PHONE : (800) 223 - 1918
FAX NUMBER : (800) 500 – 9812
===================================================================================================================
Section 2 -- COMPOSITION/INFORMATION ON HAZARDOUS INGREDIENTS
% by WT CAS No. INGREDIENT UNITS VAPOR PRESSURE
===================================================================================================================
1 - 5% 123-86-4 n-butyl Acetate 11.5
ACGIH TLV 150 ppm
ACGIH STEL 200 ppm
OSHA PEL 150 ppm
OSHA STEL 200 ppm
5 - 20% 79-20-9 Methyl Acetate 162.70
ACGIH TLV TWA: 200 ppm
ACGIH STEL 250 ppm
OSHA PEL TWA: 200 ppm
OSHA STEL 250 ppm
5 - 20% 67-64-1 Acetone 185
ACGIH TLV TWA: 500 ppm
ACGIH STEL 750 ppm
OSHA PEL TWA: 1000 ppm
OSHA STEL 1000 ppm
5 - 20% 110-43-0 Methyl n-Amyl Ketone 2.2
ACGIH TLV TWA: 100 ppm, 465 mg/m3
OSHA PEL TWA: 100 ppm 465 mg/m3
< 1% 64742-89-8 Aliphatic Naphtha 5.2
ACGIH TLV TWA: 300 ppm
OSHA PEL TWA: 300 ppm
< 1% 1330-20-7 Xylene 9
ACGIH TLV 150 ppm
ACGIH STEL 150 ppm
OSHA PEL 100 ppm
OSHA STEL 150 ppm
20 - 50% 98-56-6 Parachlorobenzotrifluoride 5.3
ACGIH TLV N/E
ACGIH STEL N/E
OSHA PEL N/E
OSHA STEL N/E
< 1% 100-41-4 Ethylbenzene 1.333
ACGIH TLV 100 ppm
ACGIH STEL 125 ppm
OSHA PEL 100 ppm
OSHA STEL 125 ppm
< 1% 77-58-7 Dibutyltin Dilaurate <1.00
ACGIH TLV TWA: 0.1 mg/m3
ACGIH STEL 0.02 mg/m3; skin
OSHA PEL TWA: 0.1 mg/m3
OSHA STEL N/E
1 - 5% 1333-86-4 Carbon Black 0
ACGIH TLV 3.5 mg/m3
ACGIH STEL N/E
OSHA PEL 3.5 mg/m3
OSHA STEL N/E
< 1% 96-48-0 Butyrolactone 3.2
ACGIH TLV N/E
ACGIH STEL N/E
OSHA PEL N/E
OSHA STEL N/E
< 1% 98-82-8 Isopropyl Benzene 8
ACGIH TLV 50 ppm
ACGIH STEL N/E
OSHA PEL 50 ppm
OSHA STEL N/E
1 - 5% 64742-95-6 Solvent Naphtha, petroleum, light aromatic 0
ACGIH TLV 100 ppm
ACGIH STEL 100 ppm
OSHA PEL 100 ppm
OSHA STEL 100 ppm
5 - 20% 65997-17-3 Silica, amorphous, precipitated and gel N/A
ACGIH TLV TWA: 10 mg/m3 inhalable
ACGIH STEL N/E
OSHA PEL N/E
OSHA STEL N/E
< 1% Mixture Diethylbenzene Isomer Mixture 1.3 mbar
ACGIH TLV
ACGIH STEL
OSHA PEL
OSHA STEL
< 1% 41556-26-7 Bis(1,2,2,6,6-Pentamethyl-4-piperidinyl) Sebacate
ACGIH TLV
ACGIH STEL
OSHA PEL
OSHA STEL
===================================================================================================================
Section 3 -- HAZARDS IDENTIFICATION
===================================================================================================================
ROUTES OF EXPOSURE:
Exposure may be by INHALATION and/or SKIN or EYE contact, depending on conditions of use. To minimize exposure, follow recommendations for proper use, ventilation, and personal protective equipment.
EFFECTS OF OVEREXPOSURE:
Irritation of eyes, skin and upper respiratory system. May cause nervous system depression. Extreme overexposure may result in unconsciousness and possibly death.
SIGNS AND SYMPTOMS OF OVEREXPOSURE:
Headache, dizziness, nausea, and loss of coordination are indications of excessive exposure to vapors or spray mists. Redness and itching or burning sensation may indicate eye or excessive skin exposure.
MEDICAL CONDITIONS AGGRAVATED BY EXPOSURE:
None generally recognized.
CANCER INFORMATION:
FOR COMPLETE DISCUSSION OF TOXICOLOGY DATA REFER TO SECTION 11.
===================================================================================================================
Section 4 -- FIRST AID MEASURES
===================================================================================================================
If INHALED:
If affected, remove from exposure. Restore breathing. Keep warm and quiet.
If on SKIN:
Wash affected area thoroughly with soap and water. Remove contaminated clothing and launder before re-use.
If in EYES:
Flush eyes with large amounts of water for 15 minutes. Get medical attention.
If SWALLOWED:
Do not induce vomiting. Get medical attention immediately.
===================================================================================================================
Section 5 -- FIRE FIGHTING MEASURES
===================================================================================================================
FLASH POINT LEL UEL
-20 F 0.8 16.0
EXTINGUISHING MEDIA:
Use National Fire Protection Association (NFPA) Class B extinguishers (carbon dioxide, dry chemical, or universal aqueous film forming foam) designed to extinguish NFPA Class IB flammable liquid fires. Water spray may be ineffective. Water spray may be used to cool closed containers to prevent pressure build-up and possible auto ignition or explosion when exposed to extreme heat.
UNUSUAL FIRE AND EXPLOSION HAZARDS:
Containers may explode when exposed to extreme heat. Application to hot surfaces requires special precautions. During emergency conditions overexposure to decomposition products may cause a health hazard. Symptoms may not be immediately apparent. Obtain medical attention.
SPECIAL FIRE FIGHTING PROCEDURES:
Full protective equipment including self-contained breathing apparatus should be used. Water spray may be ineffective. If water is used, fog nozzles are preferable. Water may be used to cool closed containers to prevent pressure build-up and possible auto ignition or explosion when exposed to extreme heat.
===================================================================================================================
Section 6 -- ACCIDENTAL RELEASE MEASURES
===================================================================================================================
STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED:
Provide maximum ventilation. Only personnel equipped with proper respiratory, skin, and eye protection should be permitted in the area. Remove all sources of ignition. Take up spilled material with sand, vermiculite, or other noncombustible absorbent material and place in clean, empty containers for disposal. Only the spilled material and the absorbent should be placed in this container.
===================================================================================================================
Section 7 -- HANDLING RELEASE MEASURES
===================================================================================================================
PRECAUTIONS TO BE TAKEN IN HANDLING AND STORAGE:
Keep away from heat, sparks, and open flame. Vapors will accumulate readily and may ignite explosively. During use and until all vapors are gone: Keep area ventilated - Do not smoke - Extinguish all flames, pilot lights, and heaters - Turn off stoves, electric tools and appliances, and other sources of ignition. Consult NFPA Code. Use approved bonding and grounding procedures. Contents under pressure. Do not puncture, incinerate, or expose to temperature above 120F. Heat from sunlight, radiators, stoves, hot water, and other heat sources could cause container to burst. Do not take internally. Keep out of the reach of children.
===================================================================================================================
Section 8 -- EXPOSURE CONTROLS / PERSONAL PROTECTION
===================================================================================================================
PRECAUTIONS TO BE TAKEN IN USE:
Use only with adequate ventilation. Avoid contact with skin and eyes. Avoid breathing vapor and spray mist. Wash hands after using. This coating may contain materials classified as nuisance particulates (listed "as Dust" in section 2) which may be present at hazardous levels only during sanding or abrading of the dried film. If no specific dusts are listed in section 2, the applicable limits for nuisance dust are ACGIII TLV 10 mg/m3 (total dust), 3 mg/m3 (respirable fraction), OSHA PEL 15 mg/m3 (total dust), 5 mg/m3 (respirable fraction). Removal of old paint by sanding, scraping, or other means may generate dust or fumes that contain lead.
VENTILATION:
Local exhaust preferable. General exhaust acceptable if the exposure to materials in section 2 is maintained below applicable exposure limits. Refer to OSHA Standards 1910.94, 1910.107, 1910.108.
RESPIRATORY PROTECTION:
If personal exposure cannot be controlled below applicable limits by ventilation, wear a properly fitted organic vapor/particulate respirator approved by NIOSH/MSHA for protection against materials in section 2. When sanding or abrading the dried film, wear a dust/mist respirator approved by NIOSH/MSHA for dust which may be generated from this product, underlying paint, or the abrasive.
PROTECTIVE GLOVES:
None required for normal application of these products where minimal skin contact is expected. For long repeated contact, wear chemical resistant gloves.
EYE PROTECTION:
Wear safety spectacles with unperforated side shields.
OTHER PRECAUTIONS:
Intentional misuse by deliberately concentrating and inhaling the contents can be harmful of fatal.
===================================================================================================================
Section 9 -- PHYSICAL AND CHEMICAL PROPERTIES
===================================================================================================================
PRODUCT WEIGHT 8.797 lb/gal 1054 g/l
SPECIFIC GRAVITY .060
BOILING POINT 0 – 662 F 17 - 350 C
VOLATILES 65.3 % by wt 69.9 % by vol
EVAPORATION RATE same as ether
VAPOR DENSITY eavier than air
REGULATORY VOC 3.21 lb/gal 385 g/l
ACTUAL VOC .80 lb/gal 215 g/l
===================================================================================================================
Section 10 -- STABILITY AND REACTIVITY
===================================================================================================================
STABILITY:
This product is normally stable and will not undergo hazardous reactions.
CONDITIONS TO AVOID:
None Known.
INCOMPATIBILITY:
Avoid contact with strong alkalies, strong mineral acids, or strong oxidizing agents.
HAZARDOUS DECOMPOSITION PRODUCTS:
Carbon monoxide, carbon dioxide, oxides of sulfur, oxides of barium, lowers molecular weight polymer fractions.
HAZARDOUS POLYMERIZATION:
None Known.
===================================================================================================================
Section 11 -- TOXICOLOGICAL INFORMATION
===================================================================================================================
CAS No. Ingredient Name
-------------------------------------------------------------------------------------------------------------------
123-86-4 n-butyl Acetate
LC50 RAT 4HR >13.2 m/l
LD50 RAT 13400 mg/kg
79-20-9 Methyl Acetate
LC50 RAT 4HR N/E
LD50 RAT N/E
67-64-1 Acetone
LC50 RAT 4HR N/E
LD50 RAT 5800 mg/kg
110-43-0 Methyl n-Amyl Ketone
LC50 RAT 4HR 2000-4000 ppm
LD50 RAT 1600 mg/kg
64742-89-8 Aliphatic Naphtha
LC50 RAT 4HR 3400 ppm4H
LD50 RAT 8 ml/kg
1330-20-7 Xylene
LC50 RAT 4HR 5000 ppm
LD50 RAT 4300 mg/kg
98-56-6 Parachlorobenzotrifluoride
LC50 RAT 4HR 22000 mg/l
LD50 RAT 13000 mg/kg
100-41-4 Ethylbenzene
LC50 RAT 4HR N/E
LD50 RAT 3500 mg/kg
77-58-7 Dibutyltin Dilaurate
LC50 RAT 4HR N/E
LD50 RAT 175 mg/kg
1333-86-4 Carbon Black
LC50 RAT 4HR N/E
LD50 RAT >2000 mg/m3/ 6 hr
96-48-0 Butyrolactone
LC50 RAT 4HR N/E
LD50 RAT 1540 mg/kg
98-82-8 Isopropyl Benzene
LC50 RAT 4HR 8000 ppm/4H
LD50 RAT 1400 mg/kg
64742-95-6 Solvent Naphtha, petroleum, light aromatic
LC50 RAT 4HR N/E
LD50 RAT 8400 mg/kg
65997-17-3 Silica, amorphous, precipitated and gel
LC50 RAT 4HR N/E
LD50 RAT
Mixture Diethylbenzene Isomer Mixture
LC50 RAT 4HR
LD50 RAT 3 gm/kg
41556-26-7 Bis(1,2,2,6,6-Pentamethyl-4-piperidinyl)
LC50 RAT 4HR N/E
LD50 RAT >3500mg/kg
===================================================================================================================
Section 12 -- ECOLOGICAL INFORMATION
===================================================================================================================
ECOTOXICOLOGICAL INFORMATION:
ECOTOXICITY: No Information Available
ENVIRONMENTAL FATE:
MOBILITY: No Information Available
BIODEGRADATION: No Information Available
BIOACCUMULATION: No Information Available
PHYSICAL/CHEMICAL:
HYDROLYSIS: No Information Available
PHOTOLYSIS: No Information Available
===================================================================================================================
Section 13 -- DISPOSAL CONSIDERATIONS
===================================================================================================================
WASTE DISPOSAL METHOD:
Waste from this product may be hazardous as defined under the Resource Conservation and Recovery Act
(RCRA) 40 CFR 261. Do not incinerate. Depressurize container. Dispose of in accordance with Federal, State, and
Local regulations regarding pollution.
===================================================================================================================
Section 14 -- TRANSPORT INFORMATION
===================================================================================================================
Proper Shipping Name: Consumer Commodity
NOS Technical Name: ORM-D
Hazard Class: N/A
UN Number: N/A
Packing Group: N/A
===================================================================================================================
Section 15 -- REGULATORY INFORMATION
===================================================================================================================
Canadian Regulations:
CEPA (Canadian Environmental Protection Act):
All substances in this product are listed on the Canadian Domestic Substance List (DSL) or are not required to be listed.
US Regulations:
This product contains the following substances subject to the reporting requirements of Section 313 of Title III of the Superfund Amendments and Reauthorization Act of 1986 and 40 CFR Part 372.
CAS No. CHEMICAL/COMPOUND % by WT
-------------------------------------------------------------------------------------------------------------------
1330-20-7 Xylene 0.4
100-41-4 Ethylbenzene 0.0
98-82-8 Isopropyl Benzene 0.2
TSCA CERTIFICATION:
U.S. TSCA: This product and/or all of its components are listed on the U.S. TSCA Inventory or is otherwise exempt form TSCA Inventory reporting requirements.
===================================================================================================================
Section 16 -- OTHER INFORMATION
===================================================================================================================
DISCLAIMER:
Do not handle until the manufacturer's safety precautions have been read and understood. Regulations require that all employees be trained on Material Safety Data Sheets for all products with which they come in contact. While we believe that the data contained herein is accurate and derived from qualified sources, the data are not to be taken as a warranty or representation for which we assume legal responsibility. They are offered solely for your consideration, investigation, and verification. Any use of these data and information must be determined by the user to be in accordance with applicable federal, state, provincial, and local laws and regulations.
==================================================================================================================
ENVIRONMENTAL DATA SHEET
All data given below are MAXIMUM THEORETICAL VALUES based on the product AS CURRENTLY FORMULATED. Variations
may occur on individual batches due to adjustments made during production.
PRODUCT NUMBER
CP-5810
PRODUCT NAME
2.8 VOC Vintage Hot Rod Black (Satin)
PRODUCT WEIGHT SPECIFIC GRAVITY FLASH POINT
8.797 lb/gal 1.060 -20
VOLATILE INGREDIENTS CERC. SARA HAPS PCT PCT
NAME CAS No. 313 112 by by
TC Wt Vol
-----------------------------------------------------------------------------------------------------------------
Xylene 1330-20-7 X X X 0.4 0.5
Ethylbenzene 100-41-4 X X X 0.0 0.0
Isopropyl Benzene 98-82-8 X X 0.2 0.2
=================================================================================================================
VOLATILE ORGANIC COMPOUNDS
A. Coating Density 8.80 lb/gal 1055 g/l
B. Total Volatiles 65.4 % by wt 69.9 % by vol
Exempt Volatiles 45.0 % by wt 44.1 % by vol
Water 0.0 % by wt 0.0 % by vol
C. Organic Volatiles 20.4 % by wt 25.8 % by vol
D. Percent Non-Volatile 34.6 % by wt 30.1 % by vol
E. Regulatory VOC 3.21 lb/gal 385 g/l
Actual VOC 1.80 lb/gal 215 g/l
Solids 3.04 lb/gal 364 g/l
WASTE DISPOSAL
Waste from this product may be hazardous as defined under the Resource Conservation and Recovery Act(RCRA)40
CFR 261. Waste must be tested for ignitability to determine the applicable EPA hazardous waste numbers. The
addition of reducers or other additives to this product may substantially alter the above data. Since conditions
of use are outside our control, we make no warranties, express or implied, and assume no liability in connection
with any use of this information.